There is no doubt that playing games and working is filled with a lot more joy and pleasure when you have more than one monitor connected. You need to use ALT+TAB a lot less to view everything, can have source code on one screen and the result on another, or just keep an eye on your instant messages and emails while you’re gaming. It’s all possible and once you got used to it, then you’ll miss it immensely when you don’t have it.
It can however end up costing you even more that you need a graphics card with just the right amount of outputs and connectors to match your monitor and this is where Club 3D comes to your rescue with two devices in the Sense Vision series. The MST-HUB is a multi-stream transport hub that morphs your one DisplayPort into three and the Y-cabled Docking station that takes one mDP and one USB 3.0 port and turns it into two mDP ports, three USB 3.0 ports, and one Gigabit Ethernet port.
The number of supported displays depends on the bandwidth available. The MST hub is using the ST Micro STDP 4320 which supports DisplayPort 1.2a specifications with support for up to 21.6Gbps of bandwidth. How much you have depends on your output device. With this kind of bandwidth at your disposal, you can easily run four full HD monitors at 60Hz and 32-bit colour depth and still have extra bandwidth to spare, and that from a single onboard connector.
The Club 3D MST hub can help with more, for example if you got a 4K monitor of the cheaper kind that only can do 30Hz. You can use the MST hub and resolve this by combining two screen resolutions of 1920×2160 at 60Hz to obtain a native 3840×2160 60Hz resolution by using two DisplayPort cables. This is particular useful of you only have one display port out to begin with and no way to attach two DisplayPort cables to your system, doesn’t help if the monitor has it.
Even if you don’t have a DisplayPort capable monitor the MST hub can help you, but you will need adapters to connect them. The Club3D MSTY Hub is a DP++ device which means that it can actively convert the DisplayPort signal to other types of display interfaces. An active adapter isn’t required, a passive is enough with this hub. Just keep in mind that passive adapters have a resolution limitation of 1920×1200.
AMD created Eyefinity with up to 6 displays, but Club 3d takes it to the next level as you only need a graphics card with two DisplayPort connectors and two of these MST hubs to achieve just that, being able to connect 6 monitors for the ultimate multi-screen setup.
Ultrabooks and notebooks also become more powerful with each generation, but the often only come with one display port. With the MST hub, you can easily connect multiple monitors to those and best of all, you only need to unplug one cable when you take your system with you on the go.
- Standards compliance/support:displayport v1.2a, displayport v1.1a,VESA DDM
- Standard,HDCP V2.0,DisplayId,and EDID V1.4
- Supports main link rates of 5.4 bps(HBR2),2.7 bps(HBR)and 1.62 bps(RBR) from source
- Supports 1/2/4 lanes of main link for RX side
- Supports three DP++ output port, or two dual-link DVI ports, or the combination of ports
- For DP 1.2a source,supports DP1.2a MST multi video/audio steams
- Supports 1.1 source, supports ViewXpand
- Supports DP-DP Bypass mode
- Supports AUX-CH enables SBM and I2C mapping over AUX between the source/sink and device
- Dedicated I2C slave for main processor to access the device
- Supported output resolution: up to 2560X1600@60Hz each monitor in DP1.2 MST and up to FHD/1080p in DP1.1 or DP 1.2 SST. With DP resolutions up to FHD (4K x 2K) @60Hz, 24bpp, but limited by DP bandwidth).
- Input pixel data depth 6/8/10/12 bits and supports output pixel format RGB444
- Advance WideEye SerDes technology
- Adaptive Sync technology